On this page8
  1. What a shear blade does
  2. 2-edge or 4-edge blades
  3. Example: blade for a Japanese guillotine shear
  4. How to choose the steel and hardness
  5. Why the blade gap matters
  6. Send these details for your bulk quotation
  7. How a bulk order works
  8. Where shear blades are used

Shear blades for guillotine shears, made to your drawing. TFI Co. has made steel blades since 1965. We supply factories, fabrication shops and distributors who order 50 to 5,000+ pcs. Send the size or the machine model, and our team prepares a written quotation for your quantity band.

Blade types
2-edge and 4-edge shear blades, top and bottom
Length
TFI Co. has made shearing knives up to 6,000 mm long
Made
To your drawing, to a sample, or from your machine model
Steel
Chosen for the sheet material and thickness you cut
Quantity bands
50–199 · 200–999 · 1,000–5,000 · 5,000+ pcs
Price
On request, per quantity band
Blade types
2-edge and 4-edge shear blades, top and bottom
Length
TFI Co. has made shearing knives up to 6,000 mm long
Made
To your drawing, to a sample, or from your machine model
Steel
Chosen for the sheet material and thickness you cut
Quantity bands
50–199 · 200–999 · 1,000–5,000 · 5,000+ pcs
Price
On request, per quantity band

What a shear blade does

A guillotine shear cuts sheet and plate in a straight line. It has two long blades. The bottom blade is fixed to the machine table. The top blade moves down with the beam and cuts the sheet against the bottom blade. The quality of the cut depends on three things: a sharp edge, the right steel, and the right gap between the two blades.

When the edge gets dull, the cut gets a burr, the sheet bends at the edge, and the machine needs more force. That is the time to turn the blade to a new edge, regrind it, or fit a new set.

2-edge or 4-edge blades

4-edge blades have a rectangular section. When one edge is dull, you turn or flip the blade and use the next edge. One blade gives four working edges before it needs regrinding. Most hydraulic and mechanical guillotine shears use this type.

2-edge blades have a cutting angle on one face, so only two edges can be used. Some machines need this shape. If you are not sure which type you have, send a photo of the blade end and its sizes.

Example: blade for a Japanese guillotine shear

This is one top blade that TFI Co. made for a fabrication shop. The details come from the customer drawing:

Size
3150 × 95.5 × 26.5 mm
Steel
Cr12MoV
Hardness
56–58 HRC
Fixing
15 bolts, M20 × 2.5
Size
3150 × 95.5 × 26.5 mm
Steel
Cr12MoV
Hardness
56–58 HRC
Fixing
15 bolts, M20 × 2.5

Other shear blade sizes TFI Co. has made include 3100 × 100 × 25 mm, 3100 × 75 × 25 mm, 3150 × 70 × 20 mm, 3090 × 68 × 24 mm and 2550 × 58 × 21 mm. Your size does not need to be on this list. We make to drawing.

How to choose the steel and hardness

  • Material you cut

    mild steel, stainless steel and high-strength plate wear the edge in different ways.

  • Thickness

    thick plate needs a tougher blade. A very hard edge stays sharp longer but can chip on thick or hard plate.

  • Machine

    tell us the make, model and tonnage. The blade must suit the force of the machine.

  • Your experience

    tell us how long your present blades last and how they fail (dull edge, chips or cracks). This helps us choose the right steel.

  • Material you cut

    mild steel, stainless steel and high-strength plate wear the edge in different ways.

  • Thickness

    thick plate needs a tougher blade. A very hard edge stays sharp longer but can chip on thick or hard plate.

  • Machine

    tell us the make, model and tonnage. The blade must suit the force of the machine.

  • Your experience

    tell us how long your present blades last and how they fail (dull edge, chips or cracks). This helps us choose the right steel.

Why the blade gap matters

One blade is fixed and the other is adjusted with bolts along its length. The gap between the blades must suit the sheet thickness and material, and it must be the same along the full length. If the gap is too small, the blades rub and can be damaged. If it is too large, the cut has a big burr and the sheet edge bends. Check the gap every time you fit new or reground blades.

Send these details for your bulk quotation

  • Length × width × thickness (mm), and 2-edge or 4-edge

  • Hole pattern: number of holes, hole size and spacing, or the machine make and model

  • The material and the thickest sheet you cut

  • Quantity band, and one-off or repeat order

  • Length × width × thickness (mm), and 2-edge or 4-edge

  • Hole pattern: number of holes, hole size and spacing, or the machine make and model

  • The material and the thickest sheet you cut

  • Quantity band, and one-off or repeat order

No drawing? A phone photo of the blade you use now, with a tape measure beside it, is enough to start.

How a bulk order works

  1. You send

    the sizes or drawing and your quantity band.

  2. Our team checks

    the size, steel and hole pattern, and asks if anything is missing.

  3. You receive a written quotation

    for your quantity band.

  4. You approve

    the drawing and the quotation, and production starts.

  1. You send

    the sizes or drawing and your quantity band.

  2. Our team checks

    the size, steel and hole pattern, and asks if anything is missing.

  3. You receive a written quotation

    for your quantity band.

  4. You approve

    the drawing and the quotation, and production starts.

For repeat orders, we keep your drawing, so the next order is the same blade.

Where shear blades are used

  • Hydraulic and mechanical guillotine shears

  • Sheet-metal and steel service centres

  • Coil cut-to-length and blanking lines

  • Fabrication shops cutting plate and sheet

  • Distributors who keep shear blades in stock for their customers

  • Hydraulic and mechanical guillotine shears

  • Sheet-metal and steel service centres

  • Coil cut-to-length and blanking lines

  • Fabrication shops cutting plate and sheet

  • Distributors who keep shear blades in stock for their customers

Can you make a blade for my machine model?

Yes, if you send the machine make and model, or the sizes and hole pattern of the blade you use now. We make shear blades to drawing, to a sample, or from these details.

What is the smallest order?

This page is for bulk orders from 50 pcs. If you need fewer, say so in the form and our team will tell you what is possible.

How is the price set?

The price depends on the size, the steel and the quantity band. You receive a written quotation before you order.

What is the longest blade you make?

TFI Co. has made shearing knives up to 6,000 mm long. Send your length and we will confirm.

Section
Shear and Straight Knives
Updated
19 November 2026
Reading time
4 min read

Ready to order in volume?

Orders from 50 to 5,000+ pieces. Send your size or drawing and the quantity, and our team replies with a quotation.

Request a volume quote