On this page7
  1. How a paper guillotine knife works
  2. HSS or TC inlay: which one?
  3. The bevel angle
  4. Knives TFI Co. has made
  5. Send these details for your bulk quotation
  6. How a bulk order works
  7. Where guillotine knives are used

Guillotine knives for paper cutters, made to your drawing. TFI Co. has made steel blades since 1965. We make knives for paper cutters such as Polar and Wohlenberg, in high-speed steel (HSS) or with a tungsten carbide (TC) inlay. We supply print shops, bookbinders, packaging converters, security printers and distributors who order 50 to 5,000+ pcs.

Knife types
Straight knives for single-knife paper cutters, and knives for three-knife trimmers
Edge
HSS, or tungsten carbide (TC) inlay
Machines
Polar, Wohlenberg and other paper cutters: send the model
Made
To your drawing, to a sample, or from your machine model
Quantity bands
50–199 · 200–999 · 1,000–5,000 · 5,000+ pcs
Price
On request, per quantity band
Knife types
Straight knives for single-knife paper cutters, and knives for three-knife trimmers
Edge
HSS, or tungsten carbide (TC) inlay
Machines
Polar, Wohlenberg and other paper cutters: send the model
Made
To your drawing, to a sample, or from your machine model
Quantity bands
50–199 · 200–999 · 1,000–5,000 · 5,000+ pcs
Price
On request, per quantity band

How a paper guillotine knife works

A paper cutter presses a stack of paper with a clamp. The knife moves down at an angle and cuts the whole stack in one stroke. At the bottom, the edge goes into a cutting stick, a plastic strip in the table, so the edge does not hit steel.

Every time the knife is reground, it becomes a little lower. Each machine has a minimum knife height. When the knife reaches it, the knife must be replaced. This is why print shops with steady work order knives in sets and keep one ready while the other is at the grinder.

HSS or TC inlay: which one?

  • Best for

    HSS knife
    General paper, board and print work
    TC-inlaid knife
    Long runs, coated paper, recycled board and other abrasive stock
  • Time between regrinds

    HSS knife
    Standard
    TC-inlaid knife
    Longer
  • Regrinding

    HSS knife
    Normal grinding wheel
    TC-inlaid knife
    Diamond wheel
  • Care

    HSS knife
    Tolerant of small knocks
    TC-inlaid knife
    Carbide is hard but can chip if hit; handle with care
  • Best for

    HSS knife
    General paper, board and print work
    TC-inlaid knife
    Long runs, coated paper, recycled board and other abrasive stock
  • Time between regrinds

    HSS knife
    Standard
    TC-inlaid knife
    Longer
  • Regrinding

    HSS knife
    Normal grinding wheel
    TC-inlaid knife
    Diamond wheel
  • Care

    HSS knife
    Tolerant of small knocks
    TC-inlaid knife
    Carbide is hard but can chip if hit; handle with care

The bevel angle

The bevel angle changes how the knife cuts. A smaller angle cuts soft paper cleanly. A larger angle gives a stronger edge for hard or abrasive stock. Tell us the angle your machine uses now, or the paper you cut most, and we make the knife to suit.

Knives TFI Co. has made

  • Knives for Polar 97 and Polar 115 paper cutters

  • Wohlenberg cutting knives

  • Knives for Kugler-Womako passport machines

  • HSS and TC-inlaid knives for passport printing, valuable-paper printing and newspaper presses

  • Knives for Polar 97 and Polar 115 paper cutters

  • Wohlenberg cutting knives

  • Knives for Kugler-Womako passport machines

  • HSS and TC-inlaid knives for passport printing, valuable-paper printing and newspaper presses

Your machine does not need to be on this list. We make to drawing.

Send these details for your bulk quotation

  • Knife length × height × thickness (mm)

  • Bolt hole pattern: number, size and spacing of holes

  • Machine make and model

  • Bevel angle, and HSS or TC inlay

  • Quantity band, and one-off or repeat order

  • Knife length × height × thickness (mm)

  • Bolt hole pattern: number, size and spacing of holes

  • Machine make and model

  • Bevel angle, and HSS or TC inlay

  • Quantity band, and one-off or repeat order

No drawing? A phone photo of your knife, with a tape measure beside it, is enough to start.

How a bulk order works

  1. You send

    the sizes, drawing or machine model, and your quantity band.

  2. Our team checks

    the size, hole pattern, bevel and steel, and asks if anything is missing.

  3. You receive a written quotation

    for your quantity band.

  4. You approve

    the drawing and the quotation, and production starts.

  1. You send

    the sizes, drawing or machine model, and your quantity band.

  2. Our team checks

    the size, hole pattern, bevel and steel, and asks if anything is missing.

  3. You receive a written quotation

    for your quantity band.

  4. You approve

    the drawing and the quotation, and production starts.

For repeat orders, we keep your drawing on file, so the next batch is the same part.

Where guillotine knives are used

  • Print shops and print finishing

  • Bookbinding and publishing

  • Packaging and label converting

  • Security printing: passports, cheques and valuable papers

  • Newspaper presses

  • Distributors who stock knives for paper cutters

  • Print shops and print finishing

  • Bookbinding and publishing

  • Packaging and label converting

  • Security printing: passports, cheques and valuable papers

  • Newspaper presses

  • Distributors who stock knives for paper cutters

Do you make knives for Polar cutters?

Yes. TFI Co. has made knives for Polar models such as the 97 and the 115. Send your model and the knife size.

Can the knives be reground?

Yes, until the knife reaches the minimum height for your machine. HSS knives use a normal wheel; TC-inlaid knives need a diamond wheel.

What is the smallest order?

These pages are for bulk orders from 50 pcs. If you need fewer, say so in the form and our team will tell you what is possible.

How is the price set?

The price depends on the size, the steel and the quantity band. You receive a written quotation before you order.

Machine names are trade marks of their owners and are used only to show fit. TFI Co. makes replacement parts and is not connected with the machine makers.

Section
Shear and Straight Knives
Updated
19 November 2026
Reading time
3 min read

Ready to order in volume?

Orders from 50 to 5,000+ pieces. Send your size or drawing and the quantity, and our team replies with a quotation.

Request a volume quote